Your Search: "Ceramicspeed"

Optimize your Zipp wheels with CeramicSpeed Hub Bearings to benefit from reduced friction and increased performance. The result is higher speed with the same effort as well as a higher top speed. CeramicSpeed Wheel Bearings have a proven lifetime, which is 3-5 times longer than standard bearings. All components are optimized for low friction and prolonged lifetime. This wheel kit is compatible with 1st generation non-disc Zipp NSW (before mid-2018). In The Box - 4 x 61803 bearings - 1 x 61903 bearing - 1 x 61804 bearing - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

Entirely developed, designed, and produced in Denmark by CeramicSpeed, the Oversized Pulley Wheel System for SRAM eTap is a technological advance for the cycling industry. Matching the highest quality materials with a unique design, the OSPW System delivers lower friction and longer lifetime, improving your competitive advantage. Thanks to the OSPW System for SRAM eTap, the power savings start at 40%, and the CeramicSpeed Bearings inside offers a 3-5 times longer lifespan compared to standard pulleys on the market. The watt savings with a CeramicSpeed OSPW System for SRAM eTap start at 1.6 watts. This 17/17-tooth OSPW system for SRAM eTap derailleurs is compatible with up to a 32 tooth cassette and with both short cage & WiFli derailleur bodies. The product is for 11-speed eTap and is not compatible with 12-speed SRAM eTap AXS. If you have the updated 11-speed SRAM eTap derailleur featuring the orbit clutch, you will need the CeramicSpeed OSPW System for SRAM eTap AXS derailleurs. The typical overall power savings of the OSPW System for OSPW System for SRAM eTap is 40%-60% over a stock setup. The oversized pulley wheels have lifespan that is 3-5 times longer than the commonly used standard pulleys on the market. In The Box: - Oversized Pulley Wheel System - CeramicSpeed Bearing Oil in 15ml dropper bottle - Sticker Sheet

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 30mm - Outer Diameter: 42mm - Width: 7mm

BSA is equivalent to English threading. English threading on road bikes mean a 68mm-wide, 34mm inside diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit works with 24mm diameter cranks, such as Shimano, FSA, Rotor, and others. Choose between two bearings for the cups. Standard Bearings have low drag thanks to hardened-steel races and our Ceramic balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. English threading is easy to work with, and 24mm spindles easily fit through the shell, allowing for large bearings to be employed in the outside cups. Put more of your energy into forward motion by reducing frictional drag wherever you can. CeramicSpeed Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. CeramicSpeed balls are 100% smoother and 15% harder than ceramic competition. The bearings last at least 3x longer than other bearings. In The Box: - 2 threaded cups with bearings - 2 dust covers with built-in spacers - Spacer tube - 10mm syringe of All Round Grease - Sticker sheet

SRAM's 1x Eagle component system boasts a twelve-speed cassette. We built pulleys that can handle the load better than stock. These CeramicSpeed Pulley Wheels work with less drag, adding to the power transmitted to the rear wheel while offering greater durability, going longer between replacement intervals. These pulleys are also fully compatible with the SRAM Eagle AXS derailleur. The aluminum pulleys with standard bearings are 34.4% more efficient than stock and use our low-drag, long-life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The upper and lower pulleys both have a narrow-wide tooth design with 14 teeth each. As the upper and lower pulleys have different tasks, they have different shapes. You'll find they are thus marked, and have directional arrows. These pulleys should be installed with stock SRAM pulley spacers. Save those from your old pulleys before installing CeramicSpeed. The kits come with CeramicSpeed Oil in a 15ml dropper bottle and grease in 5ml syringe. The bearings come pre-oiled. The grease can be used on the pulley bearings when riding in particularly harsh environments. In the box: - 2 x 14-tooth pulley wheels - CeramicSpeed Bearing Oil in 15ml dropper bottle - CeramicSpeed Grease in 5ml syringe - Sticker sheet

The XPro 15 is the ultimate expression in pedal technology. Created for competitive cyclists and triathletes seeking a competitive edge, the XPro 15 features CeramicSpeed watt-saving bearings, a hollow titanium axle and a super light carbon body giving you a pedal that weighs 88 grams per pedal. ICLIC, with its pre-opened engagement system, makes it super easy to clip in. The low stack height and oversized pedal platform make pedaling more efficient and comfortable.

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The BBright for SRAM DUB Road comes in two versions. The first is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: BBright - Opening diameter: 46mm - Shell width: 79mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - Spacer-tube - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 25mm - Outer Diameter: 37mm - Width: 7mm

The BB30 standard opened up design possibilities for frames. Adapting it for Shimano cranks takes a special machined aluminum threaded bottom bracket that threads into itself. Ours are finished with CeramicSpeed Bearings. You have two choices in terms of bearings. The first choice is our low drag, long life standard bearing with hardened-steel races and our super-round CeramicSpeed Balls. The second choice is our coated bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. This bottom bracket works with cranks that have 24mm spindles. Bottom brackets have several variables, but within that, CeramicSpeed standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. That's thanks to balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Bearings last at least three times longer than other bearings. Coated Bearings see another big bump in performance. The coated races see a 50% drag reduction and an improvement in bearing life of 60%. Performance can be tuned by changing the grease. All Round Grease comes installed, but can be changed for lower drag TT and Track Grease, or higher durability LongLife Grease, which adds a bit of drag but stays in the bearing when riding through messy conditions. In The Box: - 1 bottom bracket with bearings installed - 2 dust covers installed - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

UFO chain lubricant hardens to a 100% dry coating to protect against unwanted contaminants, which results in a quieter drivetrain, reduced friction and component wear. - Tested in real-world conditions to quantitatively create the most efficient mode of chain lubrication to date - The improved performance and reduced friction can save up to 5 watts for increased efficiency - *Bottle, chain and air temperature should be at or above 68F for proper application and performance - *Additional instructions and recommended application steps are included in box - 300 km per coating - More than 35 coatings per bottle - Non toxic, non-flammable, bio-degradable formula - Increased temperature stability - apply between 5-35OC / 41-95OF

The CeramicSpeed BB86 SRAM GXP Road Bottom Brackets are compatible with press-fit specific bike frames only. The shell diameter is 41mm ID, and when the bearings and cups are pressed in, they fit the 24/22mm SRAM and Quarq spindle. There are two versions of the CeramicSpeed Bearings that come installed in the cups. The first choice is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second choice is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. - This BB86 bottom bracket works with cranks that have 24/22mms, including Quarq and SRAM. - Frictional drag of CeramicSpeed Standard Bearings is typically 0.3-0.4 watts per set. That represents an average 75% drag drop versus standard bottom brackets. The hardened-steel races feature ceramic balls that are 100% smoother and 15% harder than the ceramic competition. The bearings last at least three times longer than other bearings. - Coated Bearings reduce drag further and increase service life. The coated races see a 50% drag reduction and an improvement in bearing life of 60%. In The Box: - 2 cups with bearings installed - 2 dust covers - 1mm spacer - 0.5mm spacer - GXP wave washer - Plastic cable protector - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 15mm - Outer Diameter: 24mm - Width: 5mm

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The EVO386 for SRAM DUB Road comes in two versions. The first version uses our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second version uses our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: EVO386 - Opening diameter: 46mm - Shell width: 86.5mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - Spacer-tube - 4 x 1mm spacers - 2 x 3mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The BB30 for SRAM DUB Road comes in two versions; one using our CeramicSpeed Standard Bearings and the other using our Coated Bearings for even longer lifetime and lower friction. Compatible with: - Frame: BB30 - Opening diameter: 42mm - Shell width: 68mm - Bottom Bracket Tool for installation: BBT-79 In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker Sheet

BSA comes from Birmingham Small Arms, aka English threading. English threading on mountain bikes means a 73mm-wide, 34mm-inside-diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit allows you to fit 30mm cranks, like those from Rotor or RaceFace, to fit in the tight space of this 30mm spindle. CeramicSpeed Coated Bearings are hand-built with unique CeramicSpeed Ceramic Balls installed on coated, hardened-steel races for longer life and less bearing drag compared to standard bearings. In The Box - 2 threaded cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - 10ml syringe All Round Grease - Sticker sheet

BSA is another way of stating English threading. The initialization comes from Birmingham Small Arms, which made bicycles. English threading on road bikes mean a 68mm wide, 34mm inside diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit works with 24mm diameter cranks, found on cranks from Shimano, FSA, Rotor, and others. Choose between two bearings for the cups. Standard Bearings have low drag thanks to hardened-steel races and our Ceramic balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. 24mm spindles easily fit through the shell and allow for large bearings to be employed in the outside cups. Put more of your energy into forward motion by reducing frictional drag wherever you can. CeramicSpeed Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. CeramicSpeed balls are 100% smoother and 15% harder than ceramic competition. The bearings last at least 3x longer than other bearings. In The Box: - 2 threaded cups with bearings - 2 dust covers with built-in spacers - Spacer tube - 10mm syringe of All Round Grease - Sticker sheet

The PF30 standard is widely used. To make it compatible with Shimano and other 24mm diameter cranks, as well as improve the system, select this bottom bracket. The package comes with two cups and CeramicSpeed Bearings installed. The cups have extended inner sleeves and join with a center section, reducing the likelihood of creaking and increasing the reliability of the system while also eliminating spindle rub on internal cables. The cups mate with 24/22mm crank spindles. There are two bearing options. Both Standard and Coated Bearings feature super smooth CeramicSpeed Balls and hardened-steel races. The CeramicSpeed Coated Bearings have an additional feature: a 3-micron thick metallic layer over the races. This addition makes the races smoother and harder, lowering drag and increasing life. The CeramicSpeed Standard Bearings have only 0.3-0.4 watts of frictional drag per set, an average drag reduction of 75% compared to stock bottom brackets. This is the result of great design, including hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. They also last longer. The CeramicSpeed Coated Bearings last even longer and feature even lower drag. Life increases by 60% and drag drops by 50% compared to our CeramicSpeed Standard Bearings. All Round Grease is installed in the bearings. It can be replaced for lower-drag TT and Track Grease or higher-durability LongLife Grease, which adds a bit of drag but stays in the bearing when riding through messy conditions. In The Box - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker sheet

The BB86 mountain bike standard was designed to integrate bearings into the bottom bracket for weight reduction. This kit works with the standard: it consists of two cups that are pressed into either side of the shell. There are two versions of this bottom bracket. Both come with CeramicSpeed Bearings installed into cups. The first is our long-life, low-drag Standard Bearing with hardened-steel races and our CeramicSpeed super-round, super hard balls. The second is our Coated bearing, which uses those same CeramicSpeed Balls installed on coated, hardened-steel races for longer life and less bearing drag. This CeramicSpeed BB86 Bottom Bracket meshes with cranks that have 24mm spindles, including both Shimano and FSA. CeramicSpeed standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That means an average 75% drag reduction compared to standard bottom brackets. The hardened-steel races feature CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Bearings last at least three times longer than other bearings. Coated Bearings drop friction further and increase lifespan to applying a coating to the races. The coated races see a 50% drag reduction and an improvement in bearing life of 60%. In The Box - 2 bottom bracket cups with bearings installed - 2 dust covers with integrated spacers installed - Spacer tube - 10ml syringe of LongLife Grease - Sticker sheet

BSA is another way of stating English threading. The initialization comes from Birmingham Small Arms, which made bicycles. English threading on road bikes mean a 68mm-wide, 34mm-inside-diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit allows you to fit 30mm cranks, like those from Rotor, to fit in the tight space of this 34mm spindle. Choose between two bearings types for the cups. Standard Bearings have low drag thanks to hardened-steel races and our CeramicSpeed Balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Note that the threaded extensions of this BB's cups that thread into the frame are thin, as they need to fit a 30mm spindle inside the cups. CeramicSpeed standard bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. That's thanks to balls that are 100% smoother and 15% harder than the ceramic competition. The bearings last at least 3x longer than other bearings. In The Box: - 2 threaded cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - 10ml syringe All Round Grease - Sticker sheet - Spacertube

Developed and designed entirely by CeramicSpeed, the Oversized Pulley Wheel System for Campagnolo is advanced for the optimization of bike performance. Everything from bearings to the cage is made from the highest quality materials. The oversized aluminum pulley wheels are fitted with standard or coated CeramicSpeed Bearings, which reduce friction to the minimum. The 13-tooth/19-tooth OSPW for Campagnolo provides 40% lower friction over a standard 11-tooth Campagnolo pulley wheel and fits up to a 32-tooth cassette. The OSPW for Campagnolo is compatible with all Campagnolo electronic rear derailleur (EPS) and all rear derailleurs with a mounting sleeve—no matter the age and model. At this point, this OSPW System is not compatible with the Campagnolo 12-speed Record and Super Record derailleurs. The OSPW for Campagnolo is compatible with: - Record mechanical - Record EPS - Super Record mechanical - Super Record EPS - Potenza mechanical - Chorus Please note, some models of Campagnolo rear derailleur, including all EPS models, do not feature a B-limit adjustment. While this product is still compatible with those derailleurs, it may not be possible to fit a 32 tooth cassette successfully on some bikes. When travelling, please remember to dismount your entire rear derailleur with an Allen key, as the OSPW System will not safely fit in most bike travel bags and could be damaged if left on. In The Box: - Oversized Pulley Wheel System - CeramicSpeed Bearing Oil in 15ml dropper bottle - Sticker sheet

- Includes 61803 (1) and 61903 (1) bearings and one grease syringe - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Note: 88 front and 188v9 rear hubs are on all 2014 and newer Zipp 202, 303, 404, 808 - One kit required for: Zipp Super-9, 900 tubular and Sub-9 disc rear hubs

- Includes 61803 bearings and one grease syringe - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - These 61803 bearings are not interchangable with the 88/188 hub 61803 bearings

BSA is equivalent to English threading. English threading on MTBs mean a 73mm-wide, 34mm-inside-diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit works with 24mm diameter cranks, such as Shimano, FSA, Rotor, and others. Choose between two bearing types for the cups. Standard Bearings have low drag thanks to hardened-steel races and our Ceramic balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. For MTBs, English threading, thanks to history, is pretty much the one threaded standard. It works great. 24mm spindles easily fit through the shell, allow for large bearings to be employed in the outside cups. What's more, they rarely creak and seal up well. Lots of things slow bikes down; bearings shouldn't be among them. CeramicSpeed Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. The bearings last at least 3x longer than other bearings. Coated bearings have even less drag. These bearings come packed with LongLife Grease, best for muddy conditions. For less drag when riding in cleaner environs, you can coat the bearings with either All Round Grease or lowest drag TT and Track Grease, which is designed for clean conditions. In The Box - 2 threaded cups with bearings - 2 dust covers with built-in spacers - Spacer tube - 10ml syringe of LongLife grease - Sticker sheet

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 15mm - Outer Diameter: 28mm - Width: 7mm

This is an updated version of the 3D-Printed Ti OSPW for Shimano 9100/8000. This new design has an integrated stop tower for easier mounting. The CeramicSpeed Oversized Pulley Wheel System has been proven to be the fastest pulley system in the world, providing energy savings starting at 2.4 watts over standard Shimano systems. The OSPW System for Shimano 9100/8000 is an industry-leading product, chosen by many of the world's leading cycling teams and professional triathletes. Featuring a 13-tooth upper pulley wheel and a 19-tooth lower pulley wheel to provide absolute optimization of the rear derailleur, the upper and lower oversized aluminum pulley wheels are fitted with coated CeramicSpeed Bearings for even longer lifetime and lower friction. Please note: The 9100/8000 system is not compatible with Ultegra 8000-GS or 8050-GS (medium cage) derailleurs, nor is it compatible with clutch-equipped Ultegra RD RX800 & RX805. Please see CeramicSpeed's Shimano 11 Speed Pulley Wheels for a compatible upgrade. - The overall power savings of the OSPW System for Shimano 9100/8000 reach 30%-60%, or more in some cases, over a stock setup. - The oversized pulley wheels have 3-5 times longer lifetime than the commonly used standard pulleys on the market. - The Shimano 9100/8000 OSPW system is compatible with up to a 32-tooth cassette for both Dura Ace & Ultegra derailleurs. In The Box: - A complete 3D-printed 13-tooth/19-tooth OSPW System - CeramicSpeed Bearing Oil in 15ml dropper bottle

Improve the performance of your 11-speed Shimano rear derailleur with pulleys that reduce friction and increase bearing life. Ours are designed to work with less drag, adding to the power transmitted to the rear wheel. Our Titanium Pulley Wheels for Shimano 11s are available with CeramicSpeed Coated Bearings that add an extra layer to the performance of the product. The Coated Bearings have races 75% harder than our hardened-steel races. They last 60% longer than our Standard Bearings. Bearing drag is decreased by over 50% compared to our Standard Bearings. Both our Standard and Coated come with the same super-hard, super-round CeramicSpeed Balls. Designed in light and strong machined Titanium, these Pulley Wheels offer three times the lifespan of our alloy Pulley Wheels, and are compatible with all 11-speed Shimano derailleurs. - There is both an upper and lower-specific pulley in the set. They are marked accordingly and have directional arrows, as well. - These pulleys are compatible with all Shimano 11-speed rear derailleurs, both mechanical and electronic. - The kits come with CeramicSpeed oil in a 15ml dropper bottle, and the bearings come pre-oiled. In the box: - 2 x 11-tooth pulley wheels - 4 x spacers - CeramicSpeed Bearing Oil in 15 ml dropper bottle - Sticker sheet

This is an updated version of the Oversized Pulley Wheel System for Shimano 9100/9150 and 8000 SS/8050 SS. This new design has an integrated stop tower for easier mounting. The CeramicSpeed Oversized Pulley Wheels System has been proven to be the fastest pulley system in the world, providing energy savings starting at 2.4 watts compared to standard Shimano systems. The OSPW System for Shimano 9100/9150 and 8000 SS/8050 SS is an industry-leading product, chosen by many of the world's leading cycling teams and professional triathletes. It features a 13-tooth upper pulley wheel and a 19-tooth lower to provide absolute optimization of the rear derailleur, and these oversized aluminum pulley wheels come fitted with either standard or coated CeramicSpeed Bearings: your choice. The Shimano 9100/8000 OSPW system is compatible up to a 32 tooth cassette for both Dura Ace & Ultegra derailleurs The typical overall power savings of the OSPW System for Shimano 9100/9150/8000 is 30%-60% over a stock setup. The oversized pulley wheels have lifespan that is 3-5 times longer than the commonly used standard pulleys on the market. Please note: The OSPW System for 9100/9150 and 8000 SS/8050 SS is NOT compatible with Ultegra 8000-GS or 8050-GS (medium cage) derailleurs, nor with the clutch-equipped Ultegra RD RX800 & RX805. Choose CeramicSpeed's OSPW X for Shimano RX800/805 for a compatible RX800 & RX805 version. For a compatible upgrade for Ultegra 8000-GS or 8050-GS choose their Pulley Wheels for Shimano, 11s NW. In The Box: - A complete 13-tooth/19-tooth OSPW System - CeramicSpeed Bearing Oil in 15ml dropper bottle

BBright is the Cervelo bottom bracket standard found on most of their frames, save the P5. In order to fit Shimano and FSA cranks into this oversized shell, this bottom bracket, complete with CeramicSpeed Bearings, needs to be pressed in. The BBright bottom bracket comes with either CeramicSpeed Standard or Coated Bearings installed. Super smooth, super-round CeramicSpeed Balls contained in hardened-steel races are found on both versions. The Coated version has a metallic coating laid onto the races, making it even smoother and harder, resulting in lower drag and longer life. BBright is similar to BB30, but is wider on the non-drive side. As such, the bottom bracket for running 24mm diameter cranks from Shimano, FSA, and others, is unique. The CeramicSpeed Standard Bearings last at least three times longer than other bearings. Thanks goes to hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. These have a frictional drag of 0.3-0.4 watts per set, which represents an average 75% drag reduction compared to most BBs. The CeramicSpeed Coated Bearings reduce drag by 50% compared to CeramicSpeed Standard Bearings, and show an improvement in bearing life by 60%. In The Box - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker sheet

Improve the performance of your 11-speed Shimano rear derailleur with pulleys that reduce friction and increase bearing life. Ours are designed to work with less drag, adding to the power transmitted to the rear wheel. - Uses low-drag, long-life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. - A set consists of differing upper and lower pulleys: they are marked as such and have directional arrows etched on them so you know exactly how to install them. - These pulleys are compatible with all Shimano 11-speed rear derailleurs except XT or XTR. - The kits come with CeramicSpeed oil in a 15ml dropper bottle. The bearings come pre-oiled. In the box: - 2 x 11-tooth pulley wheels - 4 x spacers - CeramicSpeed Bearing Oil in 15 ml dropper bottle - Sticker sheet

The Oversized Pulley Wheel System for SRAM Red and Force AXS features a 15-tooth upper and 19-tooth lower pulley wheel setting for maximum efficiency. The handbuilt OSPW System has two spring tension settings that offer you customized setup based on riding conditions. This OSPW System is also compatible with the 2020 11-speed SRAM Red eTap derailleurs featuring a clutch. - Pulley wheels: CeramicSpeed 15-tooth upper and 19-tooth lower - Pulley wheel material: aluminum - Cage material: carbon-reinforced PA - Bearing options: CeramicSpeed Standard or Coated - Compatibility: SRAM Red AXS and SRAM Force AXS. 2020 SRAM Red eTap 11-speed derailleur with the orbit clutch. This system is also compatible with the wider-range Force AXS medium cage derailleur - Cassette Compatibility: Fits 12-speed 10-36 tooth cassettes. Fits 11-32 tooth cassettes when used with an 11-speed clutched derailleur - Spring Tension Settings: 2-spring - Speeds: 12-speed - Discipline: Road and Gravel/Cross - Custom tool included for removal of stock cage and securing of OSPW. The factory clutch mechanism will remain intact. There is no damage or modification to the clutch for the installation of the OSPW System In the box: - Complete OSPW System for SRAM Red/Force AXS - CeramicSpeed Pulley Oil, 15 ml dropper bottle - Custom tool for removal of stock cage and securing of OSPW System